メッセージを送る
電話番号:
Changzhou Junqi International Trade Co.,Ltd
Changzhou Junqi International Trade Co.,Ltd

顧客のための価値を作成するため。完全性および双方にとって好都合。

ホーム 製品ブラシレスDCモーター運転者

12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー

12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー

  • 12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー
  • 12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー
  • 12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー
  • 12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー
12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー
商品の詳細:
起源の場所: 中国
ブランド名: JUYI
証明: CE,
モデル番号: JYQD-V7.5E
お支払配送条件:
最小注文数量: 1セット
価格: Negotiable
パッケージの詳細: PE BAG+のカートン
受渡し時間: 5-10日
支払条件: T/T、L/C、Paypal
供給の能力: 10000sets/Month
連絡先
詳細製品概要
製品名: ブラシレスDcモーター運転者板 定常電圧: 36V-72VDC
最高の流れ: 16A 働く流れ: 15A
PWMの速度制御: デューティサイクル0-100% アナログ電圧速度の規則: 0-5V
ブラシレス: ホール センサー ブラシレスdcモーターのため テクニカル サポート: はい
色: 速度のパルス信号の出力: はい

JYQD_V7.5E 36-72VDC 15A Working Current 3-Phase BLDC motor driver board for Hall effect BLDC Motor

 

12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー 0

 

Specifications

Operating Voltage DC 36V
Operating current ≤20A
Output power ≤700W
Speed control 0.1V-5V or PWM input
Operating temperature -40-85℃
Operating humidity ≤90%
Protection Overload protection, locked-rotor protection, over-current protection
Functions Speed pulse signal output, soft reversing (485,CAN port optional)
Overall dimension 63X42.5X33mm (L*W*H)
Net weight 38g
Optional component

Speed regulating potentiometer

external 5 digit tachometer


 

 

 

 

 

 

 

 

 

 

12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー 1

ATTENTION:

1: This brushless DC motor driver board is widely apply to DC Brushless with Hall sensor (120°angle) three-wire motors


2:please make sure to add heat sink when the output power more than 60W.

 
When installing the heat sink, please add insulation layer for 6pcs MOS. It will damage the driver board permanently without insulation,and also apply Heat-Conducting Silicone Grease on the insulation for better cooling.

3: As the BLDC motor factory may use different Hall sequence,if the motor start abnormal, can't start or the current getting to high, please adjust the sequence of the Hall, or the driver will be damaged.

 

4:Please offer the right voltage to the driver, do not exceed the operating range. and the driver has built-in 5V for speed control, DO NOT connect extra power supply( 5V ) into the driver for speed controlling, it will damage the driver.

 

Wiring instructions

12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー 2

1. Control port

5V Driver board internal output voltage, external potentiometer or switch for speed adjustment and reversing operation

Z/F Rotating direction control ports. Connect “5V” high level or no connect is Forward direction, connect 0 V low level or connect to GND is reverse direction.

VR Speed control port. Analog voltage linear speed regulation 0.1v -5V, The input resistance is 20K Ohm ,connect with GND when input PWM speed regulation, PWM frequency:1-20KHZ; Duty cycle 0-100%

EL Enable port control. Connect 5V or no connect to allow operation, connect GND to forbid operation.

Signal Speed pulse signal output

GNDUsed for Drive board internal control

2. Power port

MA ----motor phase A

MB ---- motor phase B

MC---- motor phase C

GND ----DC-

VCC----DC +

3:Hall sensor port

Ha--- Hall a

Hb---Hall b

Hc---Hall c

GND---GND

5V---5V output

4. Use shielded wires if the drivers board has more than 50 cm distance from the motor, otherwise it may lead to abnormal driving, affecting the normal use.

5. Control port distance: 2.54mm,Power port distance:3.96 mm

6. Pay attention to the insulation between the driver MOSFET and the heatsink or the installation plate.

 

 

12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー 3

12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー 4

 

Mounting dimension

12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー 5

 

12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー 6

12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー 712V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー 8

We can supply extra assy for this driver board connector wires, heatsink.

12V、24V、36V、5A、10Aの15A 700WブラシレスDCモーター運転者、ホール センサー、ブラシレスDCのモータ速度のコントローラー 9

 

連絡先の詳細
Changzhou Junqi International Trade Co.,Ltd

コンタクトパーソン: Ivanzhu

電話番号: 0086-13961407941

私達に直接お問い合わせを送信
Changzhou Junqi International Trade Co.,Ltd
No.28 Shunyuan Rdの常州都市、江蘇、中国
電話番号:86-1396-1407941
携帯サイト プライバシー政策 | 中国 よい 品質 ブラシレスDcの電動機 サプライヤー. © 2021 - 2024 bldcelectricmotor.com. All Rights Reserved.